When we talk about extracting oil from oilseeds, the actual extraction step – whether mechanical pressing or solvent-based – often gets all the attention. But the real story begins much earlier. Every step in the process determines the ultimate efficiency of any extraction method, and the quality of what goes into the extractor depends entirely on how well the seeds were prepared beforehand. These preparatory steps are called unit operations, and without them, oil yields drop, equipment wears faster, and final oil quality suffers. Here is a clear look at each of these essential operations and why they matter.
Table of Contents
- What are unit operations in oilseed processing?
- Drying: getting moisture levels right before anything else
- Cleaning: removing everything that isn’t seed
- Storage: preserving quality between harvest and processing
- Dehulling: removing the outer shell to unlock oil efficiency
- Size reduction: breaking seeds down for better processing
- Flaking: maximizing surface area for efficient extraction
- Heat treatment: conditioning seeds for optimal extraction
- Why each step connects to the next
What are unit operations in oilseed processing?
Unit operations are the individual, standardized processing steps that oilseeds go through before oil extraction begins. Most oilseeds go through the process of cleaning, drying, dehulling, size reduction, flaking, cooking, and tempering, though the exact sequence varies depending on the physical properties and oil content of the specific seed being processed. Together, these steps condition the seeds to a state where maximum oil can be efficiently and cleanly recovered.
The main aims of oilseed preparation include weakening or breaking the walls of oil-containing cells, increasing oil extraction from seeds with high oil content, and shaping the material to facilitate solvent access to the oil. Each unit operation contributes to one or more of these goals.
Drying: getting moisture levels right before anything else
Moisture content is one of the most critical variables in oilseed processing, and it must be managed from the very beginning. Most oilseeds harvested will need to be dried to some extent for both storage and pressing – even when moisture content is acceptable for storage, most seeds do not press well unless their moisture content is around 7-9%.
The moisture content of oilseeds often needs to be reduced to minimize degradation in storage and to improve the effectiveness of downstream processing. For example, soybeans are often received at 13% moisture and need to be dried to 10% to facilitate efficient hull removal. Seeds that are too wet cause problems at multiple processing stages – they clog equipment, reduce pressing efficiency, and create favorable conditions for mold growth. Conversely, over-dried seeds become brittle, produce excessive fines during size reduction, and can turn to powder during pressing, which is equally damaging to oil yield and quality.
Commercial operations use mechanical dryers that circulate heated air through the seed mass. Fluid bed dryers, which introduce a high volume of air through a bed of suspended seeds, increase the efficiency of heat transfer, allowing for more rapid heating and faster moisture extraction – while also helping deactivate harmful enzymes. Careful temperature control during drying is essential, as excessively high drying temperatures can degrade valuable seed components. Research on rapeseed shows that higher drying temperatures cause faster degradation of phytosterols and other bioactive compounds, which ultimately reduces the nutritional quality of the extracted oil.
Cleaning: removing everything that isn’t seed
Raw oilseeds arriving at a processing facility contain far more than just seeds. Plant stems, leaves, stones, dust, broken seeds, weed seeds, and metal pieces all travel along from harvest. Such material may decompose and cause heating in stored seed mass, diminishing oil and meal quality. Foreign materials also damage processing equipment, contaminate the oil, and introduce off-flavors.
Cleaning uses several methods simultaneously, each targeting a specific type of contaminant. Foreign materials are typically separated by a combination of rotating or vibrating coarse screens, reels, and aspiration – a process commonly referred to as scalping. Sand and dirt are removed by fine screening, while magnetic devices remove metal contaminants. Stones that are similar in size to seeds – such as in peanut processing – cannot be screened out and must instead be removed using gravity-based destoners that exploit density differences.
Weed seeds deserve particular attention. Weed seeds present at harvest may interfere with the extraction of oil in the press and may add unwanted taste or chemicals to the pressed oil. Thorough cleaning before storage – not just before extraction – prevents these contaminants from compounding problems throughout the storage period.
Storage: preserving quality between harvest and processing
Between harvest and processing, oilseeds must be stored for varying periods. How they are stored directly determines what quality of seed enters the processing line. The rate of quality deterioration in stored oilseeds depends on the quality of grain placed in storage and management of temperature, moisture content, and insects.
High moisture content above 14-15% in seeds has an adverse effect on oil and meal quality. Oil splitting, or acid generation, may be accelerated by microbial growth and enzyme activity in high-moisture seeds. Damaged or high-moisture seeds can release significantly more carbon dioxide and generate heat through oxidation reactions, accelerating deterioration to the point of charring.
Moisture content in oilseeds must be lower than in cereal grains because the higher oil content increases the risk of moulding and quality damage. For stable long-term storage, oilseed rape, for instance, should be dried to 7.5-8% moisture content. Oilseed rape has lower moisture content targets than cereals and should not be dried below 6% – the lowest acceptable moisture content. Proper aeration cooling, pest management, and regular temperature monitoring are essential infrastructure elements for maintaining seed quality throughout storage.
Dehulling: removing the outer shell to unlock oil efficiency
Most oilseeds are enclosed in a hull or shell that contains very little oil but causes significant processing problems if left in place. Hulls and shells of oilseeds contain less than 1% oil. If not removed, hulls reduce the total oil yield by absorbing or retaining oil in the pressed cake. Furthermore, wax and color compounds present in the hulls end up in the extracted oil, and these compounds need to be removed during refining.
The proportion of hulls varies considerably between seed types. The percentage of hulls for cottonseed, sunflower seeds, and soybean are 45%, 25%, and 7%, respectively. Dehulling – also referred to as shelling or decorticating – addresses all of these issues at once. It increases the throughput capacity of extraction equipment, reduces mechanical wear from abrasive hull material, lowers fiber content in the resulting meal, and raises protein content, making the byproduct more valuable as animal feed.
The method of dehulling varies by seed type. Sunflower seeds are typically dehulled using impact methods, where seeds strike hard surfaces at high velocity to crack the hull while leaving the kernel intact. Soybeans use a combination of cracking and aspiration to separate loosened hulls. Industry standards for soybeans require less than 3.5% fiber remaining in the meal and less than 1.5% oil content remaining in the hull after dehulling – precise targets that reflect how tightly this step is managed in commercial operations.
Size reduction: breaking seeds down for better processing
After dehulling, seeds need to be broken into smaller, more uniform pieces. This step, commonly called cracking, serves a practical purpose: it makes seeds easier to heat uniformly, reduces the energy required for flaking, and begins the process of rupturing the oil-bearing cells within the seed.
Cracking mills consist of two sets of cylindrical corrugated rolls that rotate at differential speeds to break apart seed cells containing oil. The differential speed is key – it creates a shearing action that cracks the seed rather than crushing it into fine powder. Producing fines is undesirable because fine particles clog extraction equipment and trap oil rather than releasing it. During the crushing process, the seed should only be cracked, not pulverized – fine seed particles in the form of highly crushed powder are stored in the shells and cause an increase in the amount of oil remaining in the shell.
Not all seeds require this step. Small seeds such as canola, rapeseed, and corn germ are already sufficiently small and go directly to conditioning and flaking without cracking.
Flaking: maximizing surface area for efficient extraction
Flaking is one of the most impactful preparatory steps for oil extraction, particularly for solvent extraction. It uses a flaking mill – two large-diameter smooth rolls turning in opposite directions and pressed together by hydraulic cylinders – to stretch and flatten cracked seeds into thin, uniform flakes.
The thickness of the flake is a critical quality parameter. As flake thickness increases, the amount of oil remaining in the extraction cake also increases. Too thick and oil is not fully extracted; too thin and the flakes disintegrate into fines that clog the extractor. Since flakers operate with constant roll speed and at a constant roll gap, it is important that they are fed with constant capacity based on a constant bulk density – any deviation in bulk density or capacity will be reflected in varying flake thickness.
Oilseeds like soybeans are generally flaked before solvent extraction, creating thin, flat pieces that ideally measure about 0.2 to 0.3 mm thick. Once flaked, seeds should proceed to extraction as quickly as possible. Oil from cracked or flaked seeds should be extracted within 24 hours to minimize meal and oil quality deterioration.
Heat treatment: conditioning seeds for optimal extraction
The final major preparatory step before extraction is heat treatment, which encompasses both conditioning and cooking. This step serves several functions simultaneously: it lowers oil viscosity so it flows more freely, denatures seed proteins so they release oil rather than holding it, deactivates fat-splitting enzymes that would otherwise increase free fatty acid content, and gives seeds the right elasticity for efficient mechanical pressing or solvent penetration.
Processors traditionally cook seed material in steam-jacketed vessels for about 15 minutes at 90ยฐC, using steam heat to raise moisture level to 9-12% depending on the seed. The heat causes proteins in the seed to coagulate and solidify, which allows them to exit the press along with the solid meal, keeping them separate from the liquid oil. Insufficient heat leaves proteins in a semi-liquid state where they mix with the oil, making separation difficult and reducing yield.
After cracking and dehulling, seeds are processed in a conditioner where gentle heat is applied to soften the seeds to a temperature between 60 and 75ยฐC, making them malleable for subsequent fine reduction and flaking. The conditioning is important to achieve a high oil yield and to give the seed the right elasticity, preventing the flakes from finely crumbling at low humidity. Common conditioning equipment includes drum conditioners and stack conditioners, the latter typically coupled with screw presses.
For most oilseeds, thermal treatments increase the yield of extracted oil and the content of minor lipid compounds in the oil, such as polyphenols, tocopherols, and phytosterols. However, temperature control is critical – excessive heat scorches the seed material and degrades heat-sensitive nutrients. Research on rapeseed shows that conditioning at 80ยฐC increases oil yield significantly, while conditioning at 100ยฐC can actually reduce yield because the seed becomes too dry during the process. Each seed type has its own optimal temperature range, and getting this right is essential to balancing yield with oil quality.
Why each step connects to the next
These unit operations are not isolated tasks – they form an integrated sequence where the output of each step directly affects the performance of the next. Poorly dried seeds compromise dehulling efficiency. Inadequate cleaning causes equipment damage that disrupts cracking uniformity. Uneven cracking leads to inconsistent flakes. And inconsistent flakes result in lower oil recovery during extraction.
While cleaning raw materials helps avoid the wear and tear of machinery, dehulling and cooking oilseeds helps separate the meaty part of the seed from the outer shell, making it easier to extract oil. Modern processing facilities use computer-controlled systems to monitor moisture, temperature, and material flow across all these steps, ensuring that each seed entering the extractor is in precisely the right condition. The goal throughout is straightforward: present the extraction equipment with seeds that are clean, properly sized, structurally disrupted, and thermally conditioned – so that maximum oil can be recovered at minimum cost with the highest possible quality.
What do you think? Given that preparatory unit operations can significantly affect both oil yield and quality, which of these steps do you think is most critical for a small-scale oilseed processing operation to get right first? And how do you think the growing interest in cold-pressed oils – which skip heat treatment entirely – changes the importance of the other preparatory steps?
References
- https://www.andersonintl.com/mitigating-preparation-defects-in-the-solvent-extraction-process
- https://extension.okstate.edu/fact-sheets/oil-and-oilseed-processing-i.html
- https://pmc.ncbi.nlm.nih.gov/articles/PMC10459726/
- https://extension.psu.edu/cleaning-and-storage-of-oilseed
- https://www.andersonintl.com/moisture-control-is-key-to-consistent-oilseed-processing/
- https://pmc.ncbi.nlm.nih.gov/articles/PMC3423569/
- https://storedgrain.com.au/storing-oilseeds/
- https://extension.okstate.edu/fact-sheets/print-publications/fapc-food-and-agricultural-products-center/oil-and-oilseed-processing-i-fapc-158.pdf
- https://ahdb.org.uk/knowledge-library/grain-storage-moisture-targets-for-cereals-and-oilseed-rape
- https://lipidlibrary.aocs.org/edible-oil-processing/seed-preparation
- https://www.hum.com.tr/technologies/oil-fat-technologies/oilseed-preparation
- https://www.andersonintl.com/the-evolution-of-conditioning-oilseeds-before-pressing/
- https://www.sciencedirect.com/science/article/pii/S2667325821001771
- https://pmc.ncbi.nlm.nih.gov/articles/PMC6399711/
- https://kumarmetal.com/pre-conditioning-and-cooking-understanding-the-process-and-significance/
Leave a Reply